Q-See QCN8001D Manuel d'utilisateur télécharger pdf (Page 18)

34 35

2.4 CONNECTING YOUR CAMERA TO A REMOTE NETWORK

As was mentioned in the previous section, cameras connected to the same network router

as the NVR can be discovered by that system and added. Cameras on a different network

require additional steps to be connected to an NVR, and these same steps are needed if one

is going to be accessing the camera only using a computer or mobile device.

First and foremost, you will need to physically connect your camera to a router. This router can

be part of an existing network of computers, or it can be the router/modem supplied by your

Internet Service Provider (ISP) to connect you to the Internet. This connection will be made by

plugging the other end of the Ethernet cable that you connected to the camera into a router or

into an Ethernet port that connects to a router.

You cannot connect the camera to the Internet through a modem because there is no method

available to cause the modem to dial out to the ISP. Your camera will need to be directly

connected to its own power supply - whether it is a power adapter or a Power Over Ethernet

(POE) block. In the case of the latter, the POE block will then connect to the router or network.

Your camera is not designed to be connected wirelessly to a network. It is also recommended

that the router that the camera is connected to should be connected directly to the Internet

rather than to another router if Internet access is desired as multiple routers can create

problems with connectivity. You will also need to have a computer connected to the same

router - at least temporarily - to make certain settings. If, after following the instructions you

are still not able to access your NVR, please see Section 2.5 Troubleshooting Network

Connections later in this chapter.

In order to access your camera over the Internet, you will have to determine its IP address.

Each device on a network - both a LAN or the Internet - has a speciﬁc IP address. This

address is what allows different devices on the network to communicate with each other. You

will also need to conﬁrm that two ports, or openings, have been permitted by your router to

allow communication to and from your camera.

BEFORE YOU GET STARTED

You will need to have:

• Your router’s brand, model number and manual. The manual is also usually available on

your router’s manufacturer’s website.

• The “Manuals and Software” CD that came with your camera. It contains necessary

software and links to other important programs which are mentioned in this guide.

• Your router’s password (the default password should be in your router’s manual).

• Your router’s Gateway address.

If your camera is able to automatically connect to your network, you will only need your

router’s Gateway address to connect to your camera from outside of the local network.

However, if your camera is unable to connect automatically, you will need this information in

order to make the connection.

OBTAINING IP INFORMATION USING IPCONFIG IN WINDOWS

You will need to get your router settings to not only create an IP address, but for the Default

Gateway information as well.

To get the router settings:

STEP 1. To access the router’s settings you will need to enter the Command (CMD)

panel on a computer also connected to the same router.

STEP 2. Type “ipconﬁg” at the prompt

(Red arrow in Picture 2-14) to

access router settings.

STEP 3. Write down the Default Gateway

number (bottom green arrow).

A. WINDOWS XP – Select Run from

your Windows START menu (lower

left of screen) and type “cmd” after

the prompt.

Microso Oﬃce Outlook 2007

Microso Internet Explorer

All Programs

Devices and Printers

Default Programs

Help and Support

iTunes

Adobe Acrobat

Inbox Microsof... iTunes

start

Shut Down

Log Oﬀ

Run

B. WINDOWS VISTA and WINDOWS

7 – Click on the START menu

(Windows icon) in the lower left of

your screen. Type “cmd” into the ﬁeld

that says, “Search programs and

ﬁles” and hit ENTER or click on the

magnifying glass icon.

PICTURE 2-12

PICTURE 2-13

PICTURE 2-14

Microso Oﬃce Outlook 2007

Scky Notes

All Programs

Devices and Printers

Default Programs

Help and Support

Shut down

iTunes

Adobe Acrobat

cmd

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 53 54

Commentaires sur ces manuels

Pas de commentaire

Q-See QCN8001D Manuel d'utilisateur Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Caméras de sécurité Q-See QCN8001D