Q-See QT4 Manuel d'utilisateur

~ 1 ~ Quick Internet Installation Guides

~ 10 ~ ii. Go to the section below: To access the DVR through Internet Explorer iii. Otherwise, if the ports are not open, you will get the follow

~ 11 ~ To access the DVR through Internet Explorer: once you have setup the network settings on the DVR to match the settings of your router and for

~ 12 ~ Click on Custom Level Pic 4 On “Reset to” pull down menu, select “LOW” then click on “RESET” button. Click ‘Yes’ when asked: ‘Are y

~ 13 ~ To connect to the DVR from the remote computer you would then open an Internet Explorer browser window and enter the internet IP of your rout

~ 14 ~ MMYYQQ--SSEEEE DDDDNNSS SSEETTUUPP GGUUIIDDEE FFOORR QQTT44 SSEERRIIEESS DDVVRRSS NOTE: Before you setup DDNS you must first set up

~ 15 ~ d. The next screen will ask you to create a domain name. Domain names must start with an (a-z) or (0-9) and cannot contain a hyphen. Once

~ 16 ~ e. Once you have completed steps a-d, go to the Main Menu and select the Setup icon (Red box in Fig 3), then select the Network icon (Red bo

~ 17 ~ g. After you enter the information click on the Test button (Green box in Fig 6) and wait until you see the OK message in the bottom left ha

~ 18 ~ IIPPHHOONNEE AACCCCEESSSS SSEETTUUPP GGUUIIDDEE FFOORR QQTT44 SSEERRIIEESS DDVVRRSS 1. Installing through iphone/iPad. Step 1. Op

~ 19 ~ 2. Installing through PC. Step 1: Access iTunes store in PC and then login Step 2: Connect iPhone and PC Step 3: Selec

~ 2 ~ TTAABBLLEE OOFF CCOONNTTEENNTTSS RREEMMOOTTEE MMOONNIITTOORRIINNGG GGUUIIDDEE ………………………………………………………………33 MMYY

~ 20 ~ Step 6: Checkmark “synchronously apply program” and “SuperCam”, and then click “apply” button Operation Instructions for iphone/iPad 1. L

~ 21 ~ Symbol Current viewing channel Symbol Channel status Switch channels PTZ, click to switch to Fig 2 interface Snap picture Re

~ 22 ~ 5. Server list Interface 6. Configuration interface

~ 23 ~ AANNDDRROOIIDD AACCCCEESSSS SSEETTUUPP GGUUIIDDEE FFOORR QQTT44 SSEERRIIEESS DDVVRRSS Software Installation Step 1: run Go

~ 24 ~ Login Enter into server’s IP address (or domain name), user’s ID and password. Click “Remember server” to save the setting; click button

~ 25 ~ Live view Fig 1 Fig 2 Mark 1 Curren

~ 26 ~ Record playback Fig 3

~ 27 ~ Config interface Alarm setting Tick off Sound Alarm，when Video Loss/Sensor/Motion happen，trigger sound alarm; Tick off Vibrate Alarm, when

~ 28 ~ BBLLAACCKKBBEERRRRYY AACCCCEESSSS SSEETTUUPP GGUUIIDDEE FFOORR QQTT44 SSEERRIIEESS DDVVRRSS 1. You need to setup the DVR for r

~ 29 ~ If the software fails to download, please check the following: 1. Verify that the network of mobile phone is working correctly. 2. Verify t

~ 3 ~ RREEMMOOTTEE MMOONNIITTOORRIINNGG GGUUIIDDEE FFOORR QQTT44 SSEERRIIEESS DDVVRRSS Accessing the DVR from a computer attached to the sa

~ 30 ~ Enter IP address to access DVR (or domain name), user’s ID and password. Click “Remember server” to save the setting; click button can qui

~ 31 ~ Mark 1 Current viewing channel Mark 2 Channel status Switch channels PTZ, click to switch to Fig 2 interface Snap picture Full

~ 32 ~ 4. Software configuration Alarm type: Setup the type of background alarm (Video Loss/Sensor/Motion) Alarm output type: Setup prompt t

~ 33 ~ EEMMAAIILL NNOOTTIIFFIICCAATTIIOONN SSEETTUUPP GGUUIIDDEE FFOORR QQTT44 SSEERRIIEESS DDVVRRSS Enter into Main Menu and select Setup

~ 34 ~ If you have questions: Contact Us: Mailing Address:

~ 4 ~ Fig 3 DHCP Static IP: You will need to setup the network settings on the DVR to match the settings of the router that you attach the DVR t

~ 5 ~ Fig 5 Static IP For the DVRs IP address you would enter the same first 3 sets of numbers as the gateway and select a fourth set of numbers t

~ 6 ~ Fig 6 PPPoE DDNS: You can access the DVR through a static or dynamic IP address; however a dynamic address can change from time to time. How

~ 7 ~ Fig 7 DDNS PORT FORWARDING To access the DVR from a remote computer you need to forward ports 80 and 6036 from the router the DVR is attach

~ 8 ~ c. Select the make and model of your router from the list d. Click on the ‘Click here to skip this advertisement…’ link in the upper rig

~ 9 ~ f. Verify the ports are open and traffic is allowed a. Go to www.canyouse