Q-See QSHI3512 Manuel de service

High Speed Dome User’s Manual

10When there is no available order, you can use menu to set dome idle status after specified duration. The idle status includes turn to specified pre

112 Dome Function Setup There are two ways to implement dome setup: z Keyboard or Matrix z On screen display menu If you are using keyboards or m

12Aperture will go back to auto mode after initialized or pan/tilt movement or zoom. 2.3.4 Auto Backlight Compensation This function allows you to b

133 Protocol、Baud Rate、Address setup 3.1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome: z Prot

14X X X X Reserved Figure 2 protocol sheet 5 6 Baud Rate OFF OFF 9600bps ON OFF 4800bps OFF ON 2400bps ON ON 1200bps Figure 3 Baud Rate sheet 7 8

157 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF …… ………………………………………………………………… 254 OFF ON ON ON ON ON ON ON 255 ON ON ON O

164 Cable Connection 4.1 RS485 and Power Cable Connection There are three cable groups here: power cable, RS 485 and Video cable. Draw out the cabl

17Speed dome alarm signal adopts grounding connection mode. This series speed dome support two alarm input types: normal open/normal close. You can r

18 Figure 10 General connection-1 Figure 11 General connection-2 4.2.1.2 Star connection Figure 12 Star connection 4.2.2 Alarm Connection

19 Figure 13 Alarm connection 4.2.3 Keyboard Connection You can use a keyboard to control the Dome. The display and control can work simultaneously

2Table of contents 1 FEATURES AND FUNCTIONS ... 8 1.1 Features ...

20 Figure 15 Keyboard connection-2

215 Installation 5.1 Surface Dome Installation Step 1 —— Draw a location hole Bring the bracket-anchor out from the package. Draw four holes in

22 Step 5 ——Take out pads Take out the two protect pads. Note: Be careful.

23 Step 8 ——Pass cable through the bracket hole. Fix bracket and loosen M4*4 bolts. Pass the cable out through the bracket hole in G1 ½ screw h

24Please refer to chapter three cable connection. Step 12 ——Tear off transparent cover. Remove protection coating from transparent cover. Note: Be c

25 Step 3－Cable connection Step 4－Mount the dome to the ceiling Step 5－Install transparent dome 5.3 Pendant

26 Step 2 —— Make holes and inset bolts Draw four holes and screw the four expansion bolts Note: Expansion bol

27Step 5 —— Take out pads Take out two protection pads. Note: Be careful. Pay attention to the camera! Step 6 —— S

28 Note: add anaerobic adhesive in both sides of hoisting bean G1 1/1 to enhance water proof ability. (The prevent belt is not included i

29 Step 12 ——Tear off protection cover Remove the protection coating from the transparent cover. No: Be careful. Do not dirty the dome cover.

32.3 Lens Control ...

306 Menu 6.1 Screen Menu Index

31 Figure 16 Menu tree SYSTEM INFORMATION CAMERA PARAMETERS FUN

32ADDR ：001-HBAUD RATE ：9600 PARITY ：NONE PROTOCOL ：PELCO-P MODEL ：XX-SD60XX SOFTWARE ：1.20 FIRM

33You can enter the dome menu directly. Use up and down key to view the function keys. Click confirm button to go to the submenu. Highlight exit but

34INITIAL INFORMATIONSITE INFORMATION PRESET TITLE ：ON TEMPERATURE ：ON AZIMUTH/ELEV ：ON AUTO INFRARED ：ON FACTORY DEFAU

35DIGITAL ZOOM ：ONMANUAL FOCUS ：ON AUTO IRIS ：ON BRIGHT ：↑ BLC ：ON WB.MODE ：MANUAL R．GAIN ：↑ B．GAIN

36PRESET AUTO SCAN TOURING PATTERN PRIVACY MASKINGBACK EXIT PRESET NO ：001TITLE ：PRESET001 SETTING CALL BACK EXIT AUTO SCAN NO ： 001SET L

37 Move joystick to highlight AUTO SCAN, click confirm button. z AUTO SCAN NO：Here is to set auto scan number. The value ranges from 1 to 5.You can

38 Figure 27 Auto pattern The dome supports maximum 5 patterns and for each pattern dwell time limit is 60 minutes. Highlight PATTERN and clic

39 Figure 28 Window blanking Highlight PRIVACY ZONE and click confirm button. For SONY series cameras There are maximum 24 window blanking i

45 INSTALLATION ... 21 5.1 Surface Dome Inst

40PARK FUNCTION ：OFF PARK TIME ：003MIN PARK ACTION ：NONE PRESET NO ：001 AUTOSCAN NO ：001 TOURING NO ：001 PA

41ALARM NO ：01ACTION ：NONE CONTACT ：N/O PRESET NO ：001 AUTOSCAN NO：001 TOURING NO ：001 RELAY OUT ：OFF RESET DELAY ：3S S

42 Figure 31 Device control Highlight DEVICE CONTROL and click confirm button. HEATER POWER：Here is to control heater. There are three settings: aut

437 DVR Connection and Setup Note: All the operation here is based on DH-SD protocol. For PELCO protocol users there might be slightly difference.

44 Figure 33 Pan/Tilt/Zoom setup After all the settings please click save button. In one window display mode, right click mouse (click “Fn” Button i

45In Figure 35, please click direction arrows (See Figure 36 ) to adjust PTZ position. There are totally 8 direction arrows. (There are only four dir

46Here you can activate the following functions: z Preset z Patrol(Tour) z Pattern z Aux on z Aux off z Auto scan z Auto pan z Light on

477.3.3 Patrol Setup (Tour setup) In Figure 38, click patrol button. The image is shown as in Figure 41. Input preset number and add this preset to

48Figure 35, use direction arrows to select camera left limit Then please go to Figure 43 and click left limit button Repeat the above procedures t

49Current device：dome RS485 address：1 ID: 0 8 Network Keyboard Operation (based on DH-SD) Note: all the operations here are based on DH-SD protocol.

57.3.8 Activate Auto Scan...

50Click ID and then input ID, system goes to current device connection dialogue box. Click MENU system pops up a dialogue. You can use this menu t

51Scan Value ：1 Scan setup ＞Left limit Versatile scan Right limit Random scan Speed Speed：5 〈Zoom〉 〈Direction〉

52Scan Value ：1 Scan setup ＞ start Versatile scan Stop Random scan Speed Scan Value ：1

53Pattern Value：1 Patter setup ＞ Start Rotation Stop Pattern Value：1Pattern setup Start P

549 For PELCO-P/D/P1/D1 Protocol 9.1 DVR Menu Setup In DVR menu, from system setting to PTZ control. The image is shown as below. See Figure 45. •

55 Figure 46 select PTZ Select Pan/tilt/zoom, system pops up an image. See Figure 47. Figure 47 PTZ Step is to control direction. Input valu

56Note: • When you are using front panel, you can just control four directions: up/down/left/right. • 3D intelligent positioning function is only

57 Figure 50Preset operation 9.2 From DVR Menu to Dome Menu In Figure 50 , input preset value 28 or 95 and click preset button. System pops up dome

58You can click ID button to enter current device connection interface. Highlight connection type and then click ENTER to s

59• You can only implement dome menu operation after you enter dome menu setup. Exit dome menu if you wan to control PTZ movement. “Iris Open” is wo

6Welcome Thank you for purchasing our integrated speed dome system! This operating manual is designed to be a reference tool for the installation and

60SYSTEM INFORMATION CAMERA PARAMETERS ZFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET ZAUTO SCAN TOURING PATTERN PRIVACY MA

SYSTEM INFORMATION CAMERA PARAMETERS ZFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN ZTOURING PATTERN PRIVACY MASK

62SYSTEM INFORMATION CAMERA PARAMETERS ZFUNCTION SETTING ALARM SETTING DEVICE CONTROL EXIT PRESET AUTO SCAN TOURING ZPATTERN PRIVACY MA

6310 FAQ 10.1 Daily Maintenance Please clean dome cover regularly to get vivid image. Handle the cover with care. Use water to wash. Don’t use c

64During camera switch, there is a tilt movement in the monitor. Camera power is not in the same Phase When several domes are connected to one trans

7Important Safeguards and Warnings 1．Electrical Safety All installation and operation should conform to local electrical safety codes. We assume no l

81 Features and Functions 1.1 Features Integrated dome system has the following features: z High resolution integrated digital processing camera.

9Add addresses into a routine in a desired order and then set time and stop duration for each address. The dome will begin an auto touring between th